4-20 mA / HART
|
|||||||||||
|
4-20 mA / HART
|
|||||||||||
Pressure Transmitters
LD301
Smart Pressure Transmitter Series
| Output | Two-wire, 4-20 mA output plus direct digital communication (HART protocol) |
| Range | 0 to 0.5 in H2O up to 0 to 5800 psi |
| Accuracy | +-0.1 % of the calibrated range |
| Rangeability | Accepts calibration from URL to URL/40 |
| Wetted Parts | 316 SS, Hastelloy, Tantalum |
| Ambient Temperature | -40 to 85 C |
| Display | Alpha-numeric (optional) |
| Configuration and Adjustment | Through HART communication or local |
| Hazardous Area Certification | Explosion proof, weather proof and intrisically safe |
| The LD301 Series is a complete line of differential,
gage and absolute wide range pressure transmitters. The models include
flush diaphragm and sanitary flange for liquid level measurement, Hydrostatic
Tank Gauging - HTG (model LD301-T) and wetted parts in several materials
for suiting process requirements. All models can be supplied with various
remote seals (ask for a remote seal brochure).
The CONF 301 is a configuration interface developed for the LD301. |
LD291 Low Cost Intelligent Pressure Transmitters
| Output | Two-wire, 4-20 mA output plus direct digital communication (HART protocol) |
| Range | 0 ~ 1.25 Pa to 0 ~ 25 MPa (0 ~ 5 in H2O to 0 ~ 3600 psi) |
| Accuracy | +- 0.2% accuracy of the calibrated span |
| Rangeability | Accepts calibration from URL to URL/40 |
| Wetted Parts | 316 SS or Hastelloy |
| Ambient Temperature | - 40 to 85 C |
| Display | Alpha-numeric (optional) |
| Configuration and Adjustment | Through HART communication or local |
| Hazardous Area Certification | Explosion proof, weather proof and intrisically safe |
| The LD29X series is the economical alternative in routine
gage pressure measurement. The lightweight design eliminates the need for
mounting brackets and transmitter supports in many applications.
The model LD291 offers digital HART based communication simplifying calibration and providing remote diagnostics. Its microprocessor-based electronics allow for total interchangeability with SMAR capacitive sensor. It automatically corrects sensor characteristic changes caused by temperature fluctuations. |
LD290 Low Cost Pressure Transmitters
| Output | 4-20 mA |
| Range | 0 ~ 1.25 Pa to 0 ~ 25 MPa (0 ~ 5 in H2O to 0 ~ 3600 psi) |
| Accuracy | +- 0.2% accuracy of the calibrated span |
| Rangeability | Accepts calibration from URL to URL/40 |
| Wetted Parts | 316 SS or Hastelloy |
| Ambient Temperature | - 40 to 85 C |
| Display | Optional 41/2-digit numerical and 5-character alphanumerical LCD indicator |
| Local Adjustment | Zero, span and damping |
| Hazardous Area Certification | Explosion proof, weather proof and intrisically safe |
| The LD29X series is the economical alternative in routine
gage pressure measurement. The lightweight design eliminates the need for
mounting brackets and transmitter supports in many applications.
The model LD290 is a pure 4-20 mA transmitter. Besides its analog output, its microprocessor-based electronics allow for total interchangeability with SMAR capacitive sensors. It automatically corrects sensor characteristic changes caused by temperature fluctuations. |
Temperature Transmitters
TT301 Intelligent Temperature Transmitter
| Input | Single unit accepts signal from:
|
| Output | Two-wire, 4-20 mA output plus direct
digital communication
(HART protocol) |
| Accuracy | +-0.02 % basic accuracy |
| Ambient Temperature | -40 to 85 C |
| Display | Alpha-numeric (optional) |
| Configuration and Adjustment | Through HART communication or local |
| Control | Optional PID control function with programmable setpoint curve |
| Hazardous Area Certification | Explosion proof, weather proof and intrisically safe |
| The Smar TT301 is a powerful and extremely versatile
programmable temperature transmitter, which can be used with practically
all relevant temperature sensors as well as with load cells, resistance
position indicators, etc. The TT301 transmitter is suitable for direct
field installation, being weather and explosion proof as well as intrisically
safe.
As the same unit can be used for different measuring ranges and many types of sensors, the plant can be standardized using the TT301 in measurements where different types of conventional (analog) transmitters were previously necessary. This drastically reduces calibration and maintenance time, spare part requirements and trainning. It also allows the TT301 to be purchased before measurement and control parameters are known. |
Controllers
LC 700
Programmable Logic
Controller
 |
|
Since 1978, Smar has been a powerful contributor in setting the pace for the evolution of technology in the automation field. New products and new ideas to bring solutions closer to the user's dream.
The first 16 bit digital controller, the first transmitter with embedded PID control, the first commercial line of Fieldbus products for process automation, are examples of the pioneering achievements of Smar.
The LC700 now joins the family of Smar products setting up the bridge between process and manufacturing automation and Fieldbus.
Just to make your job easier !
The CONF700 is a Windows based configurator for the LC700.
CD 600 Digital Multi-Loop Single Station Controller
CD600 with Hand-Held Terminal (HT2) |
|
| The CD600 is a powerful stand alone single station controller
capable of simultaneously controlling up to 4 loops with up to 8 PIDs and
more than 120 advanced control blocks. In order to program it, one could
use either the multipurpose Hand-Held Terminal or the CONF600.
The CONF600 is a microcomputer software for DOS systems which provides users with a user-friendly graphic interface. |
Software
CONF301
Configurator for the
LD301
 |
The CONF301 is a configuration interface
developed under the application MS Windows, so the man-machine interface
is extremely friendly.
Programming, reranging, PID adjustment (optional), setpoint changing, etc. are performed by both the HT2 and CONF301, when connected in parallel to any point of the 4-20 mA line. |
CONF600 Configurator for the CD600
 |
The CONF600 is a system based on a IBM PC
or compatible which offers graphic resources and an easy to use man-machine
interface. It is capable of performing storage of configurations in floppy
or hard disks, screen hardcopies, listing of configuration parameters,
and communication with the CD600 and the Hand-Held
Terminal.
Using the CONF600 practically discards the need to consult the manual, since most block information is displayed on screen, so debugging a configuration becomes much quicker and simpler. |
CONF700 Configurator for the LC700
 |
CONF700 is a windows based configurator
for the LC700. It is easy to use and learn. The user
can configure the hardware for the LC700 system, create the control logic
through the Ladder Structure language, create User-Functions, test the
application and have it optimized.
The application can be divided in as many logic networks that the memory can fit and the user can change the execution order, disable execution for analysis and debug purpose. |
AIMAX Process Monitoring and Control Package
AIMAX®-WIN with Window Mosaic™ |
|
| Now that you've chosen Microsoft Windows as the front
end for your factory's Man Machine Interface (MMI), you need the best designed,
most powerful Windows-based process monitoring and control package. With
leading edge features such as multiple monitor support, TA
Engineering's AIMAX®-WIN software puts DCS on the desktop. AIMAX®
is software that works hard, but isn't hard to work.
AIMAX®-WIN is the first PC-based MMI software that gives the user full advantage of the Microsoft Windows graphical user interface (GUI) with the use of our unique Window Mosaic™ function. AIMAX®-WIN interfaces with your devices and provides crucial real-time information. Its comprehensive functions enable you to effectively monitor and control processes, enhance operations, and improve productivity and quality. |
